| 1. | Turbine exit temperature
涡轮出口温度 |
| 2. | Wall temperature had a remarkable effect on smog exit temperature , whereas its effect on other parameters was not obvious
壁面温度对最高燃烧温度、壁面最大热流和平均热流影响不明显，但烟气出口温度随壁面温度的升高而增加较大。 |
| 3. | If keeping compressor ' s rotating speed unchanged , wet compression can increase compressor discharge pressure and lower exit temperature at the same time
在保持压气机转速一定情况下，压气机排气压力升高，与此同时排气温度下降。 |
| 4. | Check and error analysis indicate that this model can predict billet exit temperature 10 ~ 25 minutes in advance , and the predicting error can satisfy the demands of industrial application accuracy
校验和误差分析表明，该模型能提前5 ~ 25分钟预测出钢坯的出口温度，且预测误差满足工业应用的精度要求。 |
| 5. | Under the condition of constant phosphorus mass flow rate , the smog exit temperature would increase slowly while other parameters would decrease with increasing excess air coefficient
在燃磷量不变情况下，最高燃烧温度、壁面最大热流和平均热流均随过剩空气系数的增大而减小，但烟气出口温度缓慢增加。 |
| 6. | Moreover , the furnace arch improvement has been carried on about the chain boiler dzl6 - 1 . 25 - aii of the boiler house in southvvest jiaotong university , which has improved the furnace ' s exit temperature and the thermal efficiency of the boiler
并对西南交通大学锅炉房的dzl6 - 1 25 - a型链条锅炉进行了炉拱改造，提高了该锅炉的炉膛出口温度和热效率。 |
| 7. | The alloy component and the process parameters of the precision casting ( including the exit temperature from furnace , pouring temperature , mould preheating temperature , holding time , cooling form ) have a certain influence on the problem of the blade brittles
摘要合金含量、精铸工艺参数（出炉温度、浇铸温度、模壳预热温度、保温时间、冷却方式）对叶片脆性问题存在一定的影响。 |
| 8. | The predicted results showed that maximum combustion temperature , smog exit temperature , maximum wall heat flux and averaged wall heat flux would increase with increasing phosphorus mass flow rate when excess - air coefficient or air flow rate was constant
模拟结果表明，无论过剩空气系数固定还是空气流量固定，随燃磷量的增大，最高燃烧温度、烟气出口温度、壁面平均热流和最大热流都呈上升趋势。 |
| 9. | The high - temperature properties of ti3al matrix alloy can satisfy the request of the exit temperature of the areoengine compress . but the room temperature plasticity of ti3al matrix alloy is very low , hard to shape , and manufacture ' s cost is very expensive
Ti _ 3al基合金高的高温性能可以满足飞机发动机压气机出口温度的要求，但由于ti _ 3al基合金室温塑性差，成形困难，制造成本高；而tc11两相钛合金可以在500以下温度长时间工作，用于压气机盘已比较成熟。 |
| 10. | The effects of parameters on maximum combustion temperature , smog exit temperature , maximum wall heat flux , averaged wall heat flux of a new phosphoric acid tower with circular water wall were discussed , including phosphorus consumption , excess - air coefficient , wall temperature and radiation absorption coefficient , with the mathematical model developed in part
摘要利用已建立的数学模型考察了燃磷量、过剩空气系数、壁面温度、辐射吸收系数对新型燃磷塔的最高燃烧温度、烟气排放温度、壁面最大热流和平均热流的影响。 |
